Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
Have you been in search of help and advice around Installing A Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Mounting a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably hard task. If the old bathtub is conveniently obtainable, the task can relocate easily; if you need to open a wall to remove the old tub and also place the brand-new bathtub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will require a helper to move out the old tub as well as embeded in the new one. Make certain you have qualified on your own for the task and are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is better to think about utilizing one before you start. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will certainly help you install a brand-new tub in your bathroom if you have currently gotten a new tub and also don't require to change the plan of your previous water pipes.
Your tools as well as product checklist should consist of the following:
Planning for the Setup
Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its final setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wood boards under its feet, place the bathtub in the needed position. The wooden boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the bath tub till the level checks out degree.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been used at the very least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, resulting in problems with moisture and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are marketed in tubes and cartridges, and can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is suggested to fit the tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that write-up on Tools You Need to Install a New Bathtub through an associate on a different site. If you enjoyed reading our post plz make sure you remember to share it. Thank you for your time. Visit again soon.
Ready to assist! Report this page